Airmar

Airmar 10-Conductor In-Line Cable Splice - IP67 [D00342H]

10-Conductor In-Line Cable Splice - IP67Airmar CHIRP transducers are made with cables ending in a bare wire connection. Some sounders have internal terminal blocks to which these bare wires can be...

Airmar 164WR-1 Crows Foot Transducer Wrench [164WR-1]

164WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar 164WR-2 Transducer Hull Nut Wrench [164WR-2]

164WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on B164, SS164 and SS264 housings.You can use wrench 164WR-4 to brace the housing when using this wrench.For use...

Airmar 164WR-3 Double Handle Transducer Wrench [164WR-3]

164WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar 175WR-4 Transducer Housing Wrench [175WR-4]

175WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the top of the housing to facilitate tightening of the hull nut. Use wrench...

Airmar 599 Low/High Frequency - In-Hull Chirp Transducer w/o Connector [R599C-LH]

Low/High Frequency - In-Hull Chirp Transducer without ConnectorRely on Airmar's new broadband transducers for your ultimate fishing mission. Whether you're a commercial fisherman, charter captain,...

Airmar 60WR-1 Crows Foot Transducer Wrench [60WR-1]

60WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar 60WR-2 Transducer Hull Nut Wrench [60WR-2]

60WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 60WR-4 to brace the housing when using this wrench.For...

Airmar 60WR-3 Double Handle Transducer Wrench [60WR-3]

60WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar 60WR-4 Transducer Housing Wrench [60WR-4]

60WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut.Use wrench...

Airmar 75WR-1 Crows Foot Transducer Wrench [75WR-1]

75WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar 75WR-2 Transducer Hull Nut Wrench [75WR-2]

75WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on bronze and stainless steel housings. You can use wrench 75WR-4 to brace the housing when using this wrench.For use...